Skip to main content
Auto Deposit lets you authorize a cumulative USDT spending limit from a funding wallet. When your Deposit Balance falls below your chosen trigger balance, DGrid calculates the amount needed to reach your target balance, charges the wallet within the available authorization, and credits your Deposit Balance after the transaction is confirmed. If the wallet has less USDT than the target charge, DGrid deposits the USDT available in the wallet. Go to DGrid Billing → Deposit → Auto Deposit.

​
Before you start

  • Sign in to DGrid and connect the wallet you want to use for Auto Deposit.
  • Check the network and token shown on the page. The settings window currently shows BNB Chain and USDT. Your funding wallet needs some USDT for a deposit; if it has less than the amount needed to reach the target, DGrid deposits the available USDT. You also need a small amount of BNB to pay the gas fee for the initial USDT approval.
  • Keep the balances distinct: Deposit Balance is your recharge balance inside DGrid, excluding subscription balance. It determines when Auto Deposit is triggered and how much is needed to reach the target. Your funding wallet holds the USDT onchain. Setting an approved limit does not move the full amount into DGrid upfront.
Before approving, check the network, token, and approval recipient shown on the Billing page and in your wallet prompt.

​
Set your Auto Deposit rule

  1. Open Billing and select Auto Deposit in the Deposit section.
  2. Click Set Up Auto Deposit to open Auto-deposit settings.
  3. Review and fill in the fields:
  4. Review the estimated charge and gas fee note, then click Enable Auto Deposit.
For example, set a 10 USDT trigger balance, a 200 USDT target balance, and a 1,000 USDT approved limit. If your Deposit Balance is 8 USDT when a deposit runs, reaching the target requires 192 USDT (200 − 8). With at least 192 USDT in the wallet and sufficient authorization, the charge is 192 USDT; after success, 192 USDT has been used and 808 USDT remains authorized. If the wallet has only 50 USDT, the charge is 50 USDT, bringing the Deposit Balance to 58 USDT and leaving 950 USDT of the cumulative authorization. The actual charge uses the live balances at execution. Choose a cumulative limit that fits your expected usage.

​
Complete authorization in your wallet

After clicking Enable, follow the page and wallet prompts in order:
1

Approve the USDT allowance

Confirm the transaction in your wallet after checking the network, USDT token, spender address, and approved amount. You pay the BNB gas fee for this onchain approval.
2

Sign the Auto Deposit authorization

If your wallet asks for a signature, review and sign it. This registers your Auto Deposit rule; signing does not charge the full approved limit immediately.
3

Wait for registration

The page shows authorization progress. Setup is complete when the status is Active and the funding wallet, authorization amounts, and expiry appear. A successful wallet Approve alone does not mean Auto Deposit is active.
DGrid pays the gas fees for authorization registration and subsequent Auto Deposit transactions. If the wallet transaction is rejected, the signature fails, or registration fails, follow the page’s error message and verify that the final status becomes Active.

​
Understand how charges are calculated

While Auto Deposit is Active, DGrid can start a deposit according to your balance and rule. It first calculates the amount needed to reach the target using the live Deposit Balance at execution:
The actual deposit formula assumes sufficient remaining authorization and a valid token allowance. If the funding wallet has less USDT than the target amount, DGrid makes a partial deposit using the USDT available in the wallet; your Deposit Balance may remain below the target. If the wallet has no available USDT, there is nothing to charge. If the authorization or token allowance is insufficient, follow the page prompt to re-authorize. An Auto Deposit also needs onchain confirmation and account crediting, so the Deposit Balance may not update immediately after the rule is triggered. Approved limit / Total authorization is a cumulative cap. Each successful deposit uses part of it. An amount in flight may appear under Processing; after success it moves to Used, and after failure it is released. Remaining shows what is still available. A new authorization replaces the previous one; it does not add to the old remaining amount.

​
Review and manage your authorization

  • On the Auto Deposit page, check the status and Total authorization, Used, Processing, Remaining, and Authorization expiry.
  • Click Manage to open the management dialog. Pause stops Auto Deposit; Resume turns it back on. Use Edit / Adjust Credit to change settings or the limit, and complete wallet authorization again if prompted.
  • If the remaining limit is too low, the token allowance is no longer valid, or the authorization has expired, choose Re-Authorize and complete the wallet steps again.
  • Revoke cancels the Auto Deposit authorization. Set Allowance to 0 separately removes the wallet’s USDT token spending allowance and may require another gas-paid onchain transaction. Auto Deposit will then pause because the token allowance is insufficient. To use it again, select Re-Authorize and complete the wallet authorization steps. Choose the action that matches what you intend to change.
  • Open Payment History to review deposits. Records with Type: Auto are Auto Deposits; check their amount, time, and Tx Hash. Authorizing Auto Deposit by itself does not create a deposit record.

​
Notifications

Enable completion and failure alerts in Notifications.

​
Frequently asked questions

No. That figure is the cumulative amount DGrid may charge under the authorization. A charge occurs only when an Auto Deposit is triggered and completed, for the amount needed at that time.
First check that the status is Active. If the wallet has less USDT than needed to reach the target, DGrid can still deposit the available amount; if it has no available USDT, there is nothing to charge. Also check the Remaining authorization, the wallet’s USDT allowance, and the expiry date. If the page says Paused, address the stated reason, fund the wallet, or re-authorize as appropriate. Review the displayed error if it still fails.
No. Re-authorization replaces the previous authorization and rule.
No. They are examples to show the calculation. Choose values that fit your own balance and expected usage.